Chat with us, powered by LiveChat
商品項目:16291
庫存現貨
DATE - 2022/12/12
UTC 友順 達靈頓電晶體 / 運算放大器 / 介面IC(接口IC) 產品介紹
親愛的客戶
 
您好
達靈頓電晶體(英語:Darlington transistor),或稱達靈頓對(Darlington pair)是電子學中由兩個(甚至多個)雙極性電晶體(或者其他類似的積體電路或分立元件)組成的複合結構,
通過這樣的結構,經第一個雙極性電晶體放大的電流可以進一步被放大。
這樣的結構可以提供一個比其中任意一個雙極性電晶體高得多的電流增益。
在使用集成電流晶片的情況裡,達靈頓電晶體可以使得晶片比使用兩個分立電晶體元件占用更少的空間,
因為兩個電晶體可以共用一個集極。達靈頓電晶體通常被封裝在單一的晶片裡,從外面看就像一個雙極性電晶體。
有時,積體電路晶片中會包含8個這樣的結構方便使用。
 
運算放大器(英語:Operational Amplifier,簡稱OP、OPA、op-amp、運放)是一種直流耦合,
差模(差動模式)輸入、通常為單端輸出(Differential-in, single-ended output)的高增益(gain)電壓放大器。
在這種配置下,運算放大器能產生一個比輸入端電勢差大數十萬倍的輸出電勢(對地而言)。因為剛開始主要用於加法,減法等類比運算電路中,因而得名。
 
運算放大器有許多的規格參數,例如:低頻增益、單位增益頻率(unity-gain frequency)、相位邊限(phase margin)、功耗、輸出擺幅、共模拒斥比、電源抑制比、
共模輸入範圍(input common mode range)、轉動率(slew rate)、輸入偏移電壓(input offset voltage,又譯:失調電壓)及雜訊等。

介面IC(接口IC)
接口產品包括標準接口(RS-232、RS-422、RS-423、RS-485、LVDS和USB)、I/O擴展器、電平轉換器和智
能卡與以太網專用接口、IO-Link收發器。
RS485和RS232一樣都是基於串口的通訊接口,數據收發的操作是一致的,所以使用的是同樣WinCE的底層驅動程式。但是它們在實際套用中通訊模式卻有著很大的區別,RS232接口為全雙工數據通訊模式,而RS485接口為半雙工數據通訊模式,數據的收發不能同時進行,為了保證數據收發的不衝突,硬體上是通過方向切換來實現的,相應也要求軟體上必須將收發的過程嚴格地分開。
 
產品總類 品名規格 廠牌 產品特色 流動庫存數量 汎翊網站查詢
JFET 雙通道運算放大器 TL082G-S08-R  SOP-8   UTC VCC= ±18V , GBP = 4MHz , SR = 10V/µs 15,000 點選查看即時庫存
低雜訊四路JFET運算放大器 IC TS391BG-AF5-R SOT-25  UTC 單電源 : +2V~+36V , 雙電源 : ±1V~±18V  12,000 點選查看即時庫存
JFET低頻放大 2SK303G-V3-AE3-R SOT-23  UTC RDS(ON)=250Ω 6,000 點選查看即時庫存
RS-232 驅動及接收  IC 75232G-S20-R SOP-20  UTC 三組獨立驅動器和五個接收器   點選查看即時庫存
7通道達林頓溝渠式驅動IC ULN2003G-S16-R  SOP-16  UTC VIN=30V , Io=500mA(MAX)/CH , 箝位二極管=50V  42,500 點選查看即時庫存
7通道達林頓溝渠式驅動IC ULN2003L-D16-T  DIP-16   UTC VIN=30V , Io=500mA(MAX)/CH , 箝位二極管=50V  29,500 點選查看即時庫存
8組達林頓排列 ULN2803G-S18-R  SOP-18 UTC VIN = -0.5 ~ 30V , IF=500mA 8,000 點選查看即時庫存
RS-485/RS-422半工 接收器 IC MAX485ED   SOP-8 HTC 單電源=+5V , 資料速度 : 5Mbps , ESD : AIR ± 15KV , Body ± 8KV  1,500 點選查看即時庫存
 

 
Transceiver
TJ232 RS-232 Transceiver SOP-16
MAX232 RS-232 Transceiver DIP-16
MAX485 RS-485/ RS-422 Transceiver SOP-8 / DIP-8
TJ3485 RS-485/ RS-422 Transceiver SOP-8
MAX3485 RS-485/ RS-422 Transceiver SOP-8
 
Dual Operational Amplifier with JFET Input  
Part No. Features Number of
Channels 
VCC VOS(mV)  Slew Rate(V/us) Package
Bandwidth Max Typ
TL062 Low Power Dual J-FET Operational Amplifier

* Very low power consumption
* Wide common-mode (up to Vcc+ ) and differential voltage range
* Low input bias and offset current
* Output short-circuit protection
* High input impedance J-FET input stage
* Internal frequency compensation
* Latch up free operation
* Typical supply current: 400μA
2 ±18.0V 15 1.1 DIP-8 SOP-8 
1MHz
TL072 Low Noise Dual J-FET Operational Amplifier

*Low power consumption
*Wide common-mode (up to Vcc+ ) and differential voltage range
*Low input bias and offset current
*Low noise en = 15nV / Hz (typ)
*Output short-circuit protection
*High input impedance J-FET input stage
*Low harmonic distortion:0.01%(typ)
*Internal frequency compensation
*Latch up free operation
*High slewrate:16V/ms(typ)
2 ±18.0V 10 16 DIP-8 SOP-8 TSSOP-8
4MHz
TL082 General Purpose Dual J-FET Operational Amplifier

* Low input bias and offset current
* Wide common-mode (up to Vcc+) and differential voltage range
* Output short-circuit protection
* High input impedance J-FET input stage
* Internal frequency compensation
* Latch up free operation
* High slewrate:16V/μs(typ.)
2 ±18.0V 10 16 DIP-8 SOP-8 TSSOP-8
4MHz 
 
 
4.  Voltage Comparator  
Part No. Features Number of Channels  VCC VOS(mV)  Package
PD(mW) Max
ULC831 * Very Low Supply Current: 300nA (TYP) at VS=1.4V
* Wide Supply Voltage Range: 1.4V~5.5V
* Rail-to-Rail Input
* High Speed: 6μs (TYP) at VS=1.4V
* Push-Pull Output Current Drive: 19mA (TYP) at VS=5V
* -40°C~+85°C Operating Temperature Range
1 1.4V-5.5V 0.5 SOT-25 
-
LMV331 Single General Purpose, Low Voltage,Small Pack Comparators

* Low operating voltage 2.7-5V.
* Industrial temperature range (−40°C~+85°C)
* Low supply current 60μA
* Input common mode voltage range includes ground
* Low output saturation voltage 0.2V
1 2.7V ~ 5.5V 7 SOT-23-5 SOT-353
 -
LM393 Dual Differential Comparators

* Single or dual supply operation.
* Wide operating supply range
(VCC=2V ~ 36V or ±1 ~ ±18V)
* Input common-mode voltage includes ground.
* Low supply current drain ICC=0.8mA (Typical).
* Low input bias current IBIAS=25nA (Typical).
* Output compatible with TTL, DTL, and CMOS logic system.
2 2.0V ~ 36.0V or  ±1.0V ~ ±18.0V  5 DIP-8 SOP-8 TSSOP-8
MSOP-8 DFN2020-8
600mW/420mW/350mW
LM339 Quad Differential Comparators

*Signal or Dual Supply Operation.
*Wide Operating Supply Range (VCC=2V~36V).
*Input Common-Mode Voltage Includes Ground.
*Low Supply Current Drain IF=0.8mA (Typical).
*Open Collector Outputs for Wired and Connection.
*Low Input Bias Current IBIAS=25nA (Typical).
*Low Output Saturation Voltage.
*Output Compatible with TTL, DTL, and CMOS Logic System.
4 2.0V ~ 36.0V or ±1.0V ~ ±18.0V  3 DIP-14 SOP-14 TSSOP-14
760mW/560mW/440mW
TS391/A/B/C Low Power Single Voltage Comparator

* Wide single supply voltage range or dual supplies +2V~+36V or
±1V~±18V
* Very low supply current (0.2mA) independent of supply voltage
(1mW /comparator at +5V)
* Low input bias current: 25nA typ.
* Low input offset current: ±5nA typ.
* Low input offset voltage: ±1mV typ
* Input common-mode voltage range includes ground.
* Low output saturation voltage: 250mV typ.(IOUT=4mA).
* Differential input voltage range equal to the supply voltage.
* TTL, DTL, ECL, CMOS Compatible outputs.
1 2.0V ~ 36.0V or ±1.0V ~ ±18.0V  5 SOT-25 SOT-353
500mW
UTL331/A LOW POWER SINGLE VOLTAGE COMPARATOR
* Wide single supply voltage range or dual supplies +2V~+36V or
±1V~±18V
* Very low supply current (0.4mA) independent of supply voltage
(2mW /comparator at +5V)
* Low input bias current: 25nA typ.
* Low input offset current: ±5nA typ.
* Low input offset voltage: ±1mV typ
* Input common-mode voltage range includes ground.
* Low output saturation voltage: 250mV typ.(IOUT=4mA).
* Differential input voltage range equal to the supply voltage.
*TTL, DTL, ECL, CMOS Compatible outputs.
1 ±18 or 36V 5mV SOT-25 SOT-23-5 SOT-353
360 mW/300 mW/250 mW
LMV393 Dual General Purpose, Low Voltage,Tinypack Comparators

* High Precision Comparator.
* Low Operating Voltage 2.7-5V.
* Low Supply Current 100μA/Channel (Typical).
* Low Input Bias Current 100nA (Typical).
* Low Input Offset Current 2nA (Typical).
* Input Common Mode Voltage Range Includes Ground.
* Low Output Saturation Voltage 0.2V.
2 2.7V ~ 5.0V 7 DIP-8 SOP-8 MSOP-8
-
ULC3702 DUAL MICROPOWER CMOS VOLTAGE COMPARATORS

* Push-Pull CMOS Output Drives Capacitive Loads Without Pullup
Resistor, IO=± 8mA
* Very Low Power: 100μW (Typ.) at 5V
* Fast Response Time tPLH=2.7μs (Typ.) With 5-mV Overdrive
* Single-Supply Operation: 3V ~ 16V
2 3.0V ~ 16.0V 7 DIP-8 SOP-8
725 mW ~ 1000 mW
ULC393 DUAL MICROPOWER CMOS VOLTAGE COMPARATOR

* Very Low Power: 110μW Typ at 5V
* Single-Supply Operation: 3V~16V
* On-Chip ESD Protection
2 3.0V ~ 16.0V 5 SOP-8
600 mW
ULC3491 * Very Low Supply Current: 0.85μA (Typical)
* Supply Voltage: 1.8V~5.5V
* Rail-to-Rail Input
* Input Common-Mode Range: 200-mV Beyond Supply Rails
* High Speed: 6μs
* Push-Pull CMOS Output Stage
1 1.8V ~ 5.5V  15 SOP-8 SOT-353
-


 
JFET for General purpose Application
Part No. Maximum Ratings Electrical Characteristics (TA=25℃) Package
VGDS   IG ID PD |YFS|

MIN        Typ
(mS)          (mS)
IDSS  VGS(off) CLASSIFICATION OF IDSS
SPEC. SPEC. (*TYP) Conditions SPEC. (*TYP) Conditions
MIN. Typ. MIN. MAX. VDS  VGS MIN. MAX. VDS ID
(V) (mA) (mA) (mW) (mS)          (mS) (mA)           (mA) (V) (V) (V)           (V) (V) (µA) RANK IDSS (mA)
K1875 -20 10 10 100 15 25.0 6 32 5 0 - -2.5 5 1 GR/BL/V 6-12/10-20/16-32 SOT-323 SOT-23
UK2751 -25 - 5.0 200 1.00 - 0.25 1.2 5 0 -0.5 -1.0 5 1 - - SOT-23-3 SOT-23 SOT-23S
SOT-723
2SK303 -30 10 20.0 200 2.5 6.0 0.6 12 10 0 *-1.0 -4.0 10 1 V2/V3/V4/V5 0.6-1.5/1.2-3.0/
2.5-6.0/5.0-12.0
SOT-23  TO-92 SOT-113 SOT723
2SK3666 -30 10 10.0 200 3 6.5 0.6 0.6 10 0 -0.18 -2.2 10 1 2/3/4 0.6-1.5/1.2-3.0/2.5-6.0 SOT-23
J113 -35 350 50.0 - - - 2 - 15 0 -0.5 -3.0 15 1 - - SOT-23
2SK545 -40 10 1.0 125 0.05 0.13 0.03 0.3 10 0 *-1.5 -4 10 1 B10/B11/B12 30-80/60-180/150-300 SOT-23
2SK2751 -40 2 10.0 200 2.5 - 1.4 4.7 10 0 - - - - - - SOT-23  SOT-323
UCF1923 -6.5 10 10.0 100 0.4   0.14 0.3 2 0 -0.2 -1.5 2 1 B
C
S
140~270
210~350
160~300
SOT-723
 
2.  Interface and Driver Circuit  
(a.)For RS-232 Driver
Part No. Features Vin IOS(H) VDD VSS Package
Vcc(V) IOS(L) VOH VOL
75185 Multiple RS-232 Driver & Receiver

*Single Chip with Easy Interface between UART and Serial-Port connector of PC.
*Three Drivers and five Receivers Meet or Exceed the Requirements of TIA/EIA-232-F and ITU v.28 Standards.
*Designed to Support Data Rates up to 120 kbps
4.5 ~ 5.5 -4.5~-19.5(mA) VDD=9.0V,Vss=-9.0V(Typ) DIP-20 SOP-20 SSOP-20 TSSOP-20
±7.5;±9;±15 4.5~ 19.5(mA) 7.5V(RL=3KΩ) -7.5V(RL=3KΩ)
75323 Multiple RS-232 Driver & Receiver

* Single chip with easy interface between UART and serial-port
connector
* Data rates : 20 kb/s.
* Complement to the UTC 75232.
4.5 ~ 5.5 -4.5~-19.5(mA) VDD=9.0V,Vss=-9.0V(Typ) DIP-20 SOP-20 
±7.5;±9;±13.5 4.5~19.5(mA) 7.5V(RL=3KΩ) -7.5V(RL=3KΩ)
75232 Multiple RS-232 Driver & Receiver

* Single chip with easy interconnection of the UART and
serial-port connector of personal computer.
* Meets standard TIA/EIA-232-F and ITU V.28
* Up to 120 kbps data rate
* 20-pin SOP/ DIP/SSOP/TSSOP packages
4.5 ~ 5.5 -8.5~-19.5(mA) VDD=9.0V,Vss=-9.0V(Typ) DIP-20 SOP-20 SSOP-20 TSSOP-20
±7.5;±9;±13.5 8.5~19.5(mA) 7.5V(RL=3KΩ) -7.5V(RL=3KΩ)
UT213 Enhanced RS-232 Drivers & Receivers

* Operates With 3.0V~5.5V Power Supply
* Four Drivers and Five Receivers
* Operates Up To 120 kbps
* Designed to Transmit at a Data Rate of 120 kbps
* Low Standby Current (15μA Typical)
* External Capacitors (4*0.1μF)
* Accepts 5.0V Logic Input With 3.3V Supply
* Serial-Mouse Drivability
* Exceeds ±8KV ESD Protection(HBM) for RS-232 I/O Pins
3.0 ~ 5.5  -60.0(mA) - SOP-28 SSOP-28
- 60.0(mA) 5.4V(RL=3KΩ) -5.4V(RL=3KΩ)
UT232E Enhanced RS-232 Drivers & Receivers

* Single power supply: 3.3V~5.5V
* Low power supply current: 3.0mA
* Multiple drivers and receivers
* Receiver input levels: ±25V
* 3-State outputs of TTL/CMOS receiver
* High output slew rate: 10V/μs under load
* High data rate: 120kbps under load
* Four external small charge pump capacitors: 0.1μF
* Exceeds ±8KV HBM ESD protection for RS-232 I/O pins
3.3 ~ 5.5  -18.0(mA) Vcc=5.0V DIP-16 SOP-16 SSOP-16
- 18.0(mA) 6.0V(RL=3KΩ) -6.0V(RL=3KΩ)
UT3202 MULTICHANNEL RS-232 LINE TRANSCEIVERS

* Exceeds ±8KV ESD Protection(HBM) for RS-232 I/O Pins
* Meets the Requirements of TIA/EIA-232-F and ITU V.28 Standards
* Operates With 3.0V to 5.5V VCC Supply
* Operates Up To 250kbit/s Data Rate
* Two Drivers and Two Receivers
* External Capacitors 4×0.1μF
* Accepts 5.0V Logic Input With 3.3V Supply
3.0 ~ 5.5  -60.0(mA)(Max) Vcc=5.0V SOP-16 TSSOP-16
- 60.0(mA)(Max) 5.4V(RL=3KΩ) -5.4V(RL=3KΩ)
UT3221/E MULTICHANNEL RS-232 LINE TRANSCEIVERS

* Operates With 3.0V to 5.5V Power Supply
* One Driver and One Receiver
* Operates Up To 250 kbps
* Designed to Transmit at a Data Rate of 250 kbps
* Low Standby Current (1μA Typical)
* External Capacitors (4*0.1μF)
* Accepts 5.0V Logic Input With 3.3V Supply
* Serial-Mouse Drivability
* Exceeds ±8KV ESD Protection(HBM) for RS-232 I/O Pins
3.0 ~ 5.5  -60.0(mA)(Max) - TSSOP-16 SSOP-16
- 60.0(mA)(Max) 5.4V(RL=3KΩ) -5.4V(RL=3KΩ)
UT3222 MULTICHANNEL RS-232 LINE TRANSCEIVERS

* Exceeds ±8KV ESD Protection(HBM) for RS-232 I/O Pins
* Meets the Requirements of TIA/EIA-232-F and ITU V.28 Standards
* Operates With 3.0V to 5.5V VCC Supply
* Operates Up To 250kbit/s Data Rate
* Two Drivers and Two Receivers
* Low Standby Current 1μA Typical
* External Capacitors 4×0.1μF
* Accepts 5.0V Logic Input With 3.3V Supply
3.0 ~ 5.5  -60.0(mA)(Max) Vcc=5.0V TSSOP-20 SSOP-20
- 60.0(mA)(Max) 5.4V(RL=3KΩ) -5.4V(RL=3KΩ)
UT3223 RS-232 Transceivers with AutoShutdown

* Operates With 3.0V~5.5V Power Supply
* Two Drivers and Two Receivers
* Operates Up To 250 kbps
* Designed to Transmit at a Data Rate of 250 kbps
* Low Standby Current (1μA Typical)
* External Capacitors (4*0.1μF)
* Accepts 5.0V Logic Input With 3.3V Supply
* Serial-Mouse Drivability
* Exceeds ±8KV ESD Protection(HBM) for RS-232 I/O Pins
3.0 ~ 5.5  -60.0(mA)(Max) Vcc=5.0V TSSOP-20 SSOP-20
- 60.0(mA)(Max) 5.4V(RL=3KΩ) -5.4V(RL=3KΩ)
UT3227 RS-232 Transceivers with AutoShutdown

* Operates With 3.0V to 5.5V Power Supply
* One Driver and one Receiver
* Operates Up To 1Mbps
* Designed to Transmit at a Data Rate of 1Mbps
* Low Standby Current (1μA Typical)
* External Capacitors (4×0.1μF)
* Accepts 5.0V Logic Input With 3.3V Supply
* Serial-Mouse Drivability
* Exceeds ±8KV ESD Protection(HBM) for RS-232 I/O Pins
3.0 ~ 5.5  -60.0(mA)(Max) - SSOP-16
TSSOP-20
- 60.0(mA)(Max) 5.4V(RL=3KΩ) -5.4V(RL=3KΩ)
UT3232 True RS-232 Transceivers

* Exceeds ±8KV ESD Protection(HBM) for RS-232 I/O Pins
* Meets the Requirements of TIA/EIA-232-F and ITU V.28 Standards
* Operates With 3.0V to 5.5V VCC Supply
* Operates Up To 250kbit/s Data Rate
* Two Drivers and Two Receivers
* External Capacitors 4×0.1μF
* Accepts 5.0V Logic Input With 3.3V Supply
3.0 ~ 5.5  -60.0(mA)(Max) Vcc=5.0V SOP-16 SSOP-16 TSSOP-16
- 60.0(mA)(Max) 5.4V(RL=3KΩ) -5.4V(RL=3KΩ)
UT3238 +3.3V TO +5.0V POWER SUPPLY, 250KBPS, RS-232 LINE DRIVERS/RECEIVERS

* Operates With 3.3V~5.0V Power Supply
* Five Drivers and Three Receivers
* Operates Up To 250 kbps
* Designed to Transmit at a Data Rate of 250 kbps
* Low Standby Current (1μA Typical)
* External Capacitors (4*0.1μF)
* Accepts 5.0V Logic Input With 3.3V Supply
*Always-Active Non-inverting Receiver Output (R1OUTB)
* Serial-Mouse Drivability
* Exceeds ±8KV ESD Protection(HBM) for RS-232 I/O Pins
3.3 ~ 5.5  -60.0(mA)(Max) Vcc=5.0V TSSOP-28
- 60.0(mA)(Max) 5.0V(RL=3KΩ) -5.0V(RL=3KΩ)
UT3243A 3.0V TO +5.5V POWER SUPPLY, 235KBPS,MULTICHANNAEL RS-232 LINE DRIVERS/RECEIVERS

* Operates With 3.0V ~ 5.5V Power Supply
* Three Drivers and Five Receivers
* Operates Up To 235 kbps
* Designed to Transmit at a Data Rate of 235 kbps
* Low Standby Current (1uA Typical)
* External Capacitors (4×0.1μF)
* Accepts 5.0V Logic Input With 3.3V Supply
* Always-Active Non-inverting Receiver Output (R2OUTB)
* Serial-Mouse Drivability
* ESD(HBM) Protected ±15KV(MIN.) for RS-232 Pins
3.0 ~ 5.5  -60.0(mA)(Max) Vcc=5.0V SSOP-28 TSSOP-28
QFN-32(5×5)
- 60.0(mA)(Max) 5.4V(RL=3KΩ) -5.4V(RL=3KΩ)
UT5232 3.0V TO +5.5V POWER SUPPLY, 235KBPS,MULTICHANNAEL RS-232 LINE DRIVERS/RECEIVERS

* Operates With 3.0V ~ 5.5V Power Supply
* Three Drivers and Five Receivers
* Operates Up To 235 kbps
* Designed to Transmit at a Data Rate of 235 kbps
* Low Standby Current (1uA Typical)
* External Capacitors (4×0.1μF)
* Accepts 5.0V Logic Input With 3.3V Supply
* Always-Active Non-inverting Receiver Output (R2OUTB)
* Serial-Mouse Drivability
* ESD(HBM) Protected ±15KV(MIN.) for RS-232 Pins
3.0 ~ 5.5  -60.0(mA)(Max) Vcc=5.0V SSOP-28 TSSOP-28
QFN-32(5×5)
- 60.0(mA)(Max) 5.4V(RL=3KΩ) -5.4V(RL=3KΩ)
USN75176 Differential Bus Transceiver    -250.0(mA)(Max) Vcc=4.75~5.25V DIP-8
  250.0(mA)(Max) 3.7V 1.1V
 

 
Part No. Features Output Voltage Input Voltage(Output On) Package
PD(mW) Input Voltage(Output Off)
ULN2001 3 CH Darlington Sink Driver (Ri=2.7k)

* Output Current (Single Output): 500mA max
* High Sustaining Voltage Output: 50V min
* Inputs Compatible with Various Types of Logic
* Output Clamp Diodes
* Relay-Driver Applications
0V~50.0V 2.8V ~ 12.0V DIP-8 SOP-8
750/625mW 0V ~ 0.7V
ULN2001LC 3 CH Darlington Sink Driver (Ri=2.7k)

* Output Current (Single Output): 100mA max
* High Sustaining Voltage Output: 50V min
* Inputs Compatible with Various Types of Logic
* Output Clamp Diodes
* Relay-Driver Applications
0V~50.0V 2.8V ~ 12.0V DIP-8 SOP-8
750/625mW 0V ~ 0.7V
ULN2003 7 CH Darlington Sink Driver (Ri=2.7k)

*Output Current (Single Output): 500mA (Max.)
*High Sustaining Voltage Output: 50V (Min.)
*Output Clamp Diodes
*Inputs Compatible With Various Types Of Logic
-0.5V~50.0V 2.8V ~ 24.0V DIP-16 SOP-16
TSSOP-16
1470/1250/620mW 0V ~ 0.7V
ULN2003R 7 CH HIGH VOLTAGE HIGH CURRENT DARLINGTON TRANSISTOR ARRAY (Ri=2.7k)

* Output Current (Single Output): 500mA max
* High Sustaining Voltage Output: 50V min
* Inputs Compatible with Various Types of Logic
* Output Clamp Diodes
* Relay-Driver Applications
-0.5V~50.0V 2.8V ~ 24.0V SOP-16
540/65mW 0V ~ 0.7V
ULN2004 7 CH Darlington Sink Drivers (Ri=10.5k)

*Output current (single output): 500mA (MAX.)
*High sustaining voltage output: 50V (MIN.)
*Output clamp diodes
*Inputs compatible with various types of logic
-0.5V~50.0V 6.2V ~ 24.0V DIP-16 SOP-16
1470/625mW 0V ~ 1.0V
ULN2012 HIGH VOLTAGE HIGH CURRENT DARLINGTON ARRAY

* PMOS Compatible Inputs
* Output Current to 600mA
* Output Voltage to 50V
* Transient-Protected Outputs
-0.5V~50.0V 17.0V SOP-16
1250mW -
ULN2803 8-CH Darlington Arrays (Ri=2.7k)

*Output current (single output) 500mA MAX.
*High sustaining voltage output 50V MIN.
*Output clamp diodes
*Inputs compatible with various types of logic
-0.5V~50.0V Max=2.4V DIP-18 SOP-18
SOP-20 TSSOP-20
1470/625mW -
ULN2804 8-CH Darlington Arrays (Ri=10.5k)

* Eight Darlingtons with common emitters
* TTL, PMOS or CMOS Compatible inputs
* Peak output current to 500mA
* Output voltage to 50V
* Clamp diodes for transient suppression
* DIP-28 and SOP-18 packages
0V~50.0V Max=5.0V DIP-18 SOP-18
1500/950mW -
62783 8-CH High Voltage Source Driver

*High output voltage: VCC = 50V (MIN.)
* Output current (single output) IOUT = -500mA (MIN.)
* Output clamp diodes and single supply voltage
* Input compatible with various types of logic
* TTL, 5V CMOS
50.0V(MAX) 2.0V ~ 15.0V DIP-18 SOP-18 SOP-20 TSSOP-20
1470/960mW/960mW 0V~0.8V
62784 8-CH High Voltage Source Driver

* High output voltage: VCC = 50V (MIN.)
* Output current (single output):-500mA (MIN.)
* Output clamp diodes and single supply voltage
* Input compatible with kinds of types of logic
* 6~15V PMOS, CMOS
50.0V(MAX) 4.5V ~ 30.0V SOP-18
1470/960mW 0V ~ 2.0V
ULN202L05 4-CH Darlington Sink Driver AND 3-Terminal
0.2A 5V Voltage Regulator

For Darlington Sink Drivers
* Output current (single output): 500mA max
* High sustaining voltage output: 50V min
* Output clamp diodes
* Inputs compatible with various types of logic
For 5V VOLTAGE REGULATOR
* Output Current up to 200mA
* Thermal Overload Shutdown Protection
* Short Circuit Current Limiting
Vo=-0.5V~50.0V Max=2.0V SOP-14
900mW -
ULN2018 DRIVER CIRCUIT SPECIAL PURPOSE FOR MICROWAVE OVEN
* Output current (single output): 100mA (MAX.)
* High sustaining voltage output: 50V (MIN.)
* Output clamp diodes
* TTL/CMOS logic level is compatible.
50V 5V ~ 12V SOP-16
1500 0V ~ 0.7V
ULN2020 DRIVER CIRCUIT SPECIAL PURPOSE FOR MICROWAVE OVEN
* Output current (single output): 100mA (MAX.)
* High sustaining voltage output: 50V (MIN.)
* Output clamp diodes
* TTL/CMOS logic level is compatible.
50V 5V ~ 12V SOP-16
1500 0V ~ 0.7V
ULN202 4CH DARLINGTON SINK
DRIVER

* Output Current (Single Output): 500mA (Max.)
* High Sustaining Voltage Output: 50V (Min.)
* Output Clamp Diodes
* Inputs Compatible With Various Types Of Logic
50.0V(MAX) 2.8V ~ 24.0V MSOP-10
600mW 0V ~ 0.7V